Page 1 of 2 12 LastLast
Results 1 to 10 of 19

Thread: Plumbing

  1. #1
    Royal Gramma


    Zeus's Avatar
    Join Date
    Nov 2006
    Location
    Irvine, Scotland
    Posts
    1,544
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Plumbing

    Hi all,

    Just getting around to doing my plumbing. Never done this before so was wondering what the best way to do this so that all the pipes and joints match up to the holes in the tank from start to finish?

    Cheers,
    Campbell
    something broke the surface just to see the starry dome.

    Don't drive faster than your Angel can fly

  2. #2
    Copepod



    Join Date
    Feb 2008
    Location
    Sparsholt UK
    Posts
    20
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Plumbing

    cut all the measurements etc and dry fit it first then when you are sure of layout solvent weld it together this way you dont waste anything. remember the more bends etc that you have the less the flow rate will be. double check your measurements as well before you cut. maybe draw a plan of how it will be then that way you will know where you are. hope it all goes well:D

    Ed

  3. #3
    Royal Gramma


    Zeus's Avatar
    Join Date
    Nov 2006
    Location
    Irvine, Scotland
    Posts
    1,544
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Plumbing

    Thanks Ed,

    It's the measuring/sizing bit that I am concerned with. How best to do that, especially when you get to when you have to match the pipes to the drain/return holes?

    Campbell
    something broke the surface just to see the starry dome.

    Don't drive faster than your Angel can fly

  4. #4
    Copepod



    Join Date
    Feb 2008
    Location
    Sparsholt UK
    Posts
    20
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Plumbing

    you could try numbering them all wit a permament marker and with the measuring bit just double and triple check before you cut the piping. its not as difficult as it sounds if you have it all planned out. remember to measure the bits inside the joints as i have forgoten to do it before and it is annoying when you have wasted a good bit of pipe. what size tank are you plumbing? what diameter are the inlet and outlet hoels?

    Ed

  5. #5
    Bamboo Shark



    Join Date
    Aug 2006
    Location
    durham
    Posts
    5,070
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Smile Re: Plumbing

    do as sugested fit it all together on a dry run,you only need to solvent weld the pressure pipes.derek
    66ins by 60ins by 37ins deep. fish stock 7in moorish idol,9in blue face angel,6in blue face angel,6in regal angel, 4in powder blue,1 pair flame angels,3 bellus angels,12 alleni damsels,4in cleaner wrasse,1 pair red sea clowns, 1 Pair of wild percs and 1 Pair of black percs,1 fire clown,1 red sea clown, 2 orchid dottybacks, 3 yellow tangs,2 heteractis magnifica anemones,1 heteractis crispa, 2 red bubble tips.

  6. #6
    Royal Gramma


    Zeus's Avatar
    Join Date
    Nov 2006
    Location
    Irvine, Scotland
    Posts
    1,544
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Plumbing

    Thanks guys,

    Ed, the tank is 8x2x2 with 25mm returns and 32mm drains.

    Campbell
    something broke the surface just to see the starry dome.

    Don't drive faster than your Angel can fly

  7. #7
    Copepod



    Join Date
    Feb 2008
    Location
    Sparsholt UK
    Posts
    20
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Plumbing

    shouldnt be too hard then as long as the pipework is all the right diameter. sounds like a very nice tank wish i could ahve one like that but unfortunately college fine you for having a fish tank in your rm grrr stupid people

    Ed

  8. #8
    Great White Shark
    • Tangman's Livestock
      • Fish:
      •  4 Yellow Tangs, 1 Sailfin Tang, 1 Lipstick Tang, 1 Adult Emporer Angel, 1 Flagfin Angel,1 Copperband, 1 Pair of Gold Lined Maroon Clowns. 1 Radiant Wrasse,1Potters Angel, 1 Volriki Angel, 1 Cherub Angel,1 Cleaner Wrasse
      • Corals:
      •  All soft corals mainly leathers
      • Inverts:
      •  few snails and crabs, along with 5 Brittlestars and 2 Serpent Stars


    Tangman's Avatar
    Join Date
    Aug 2006
    Location
    York/North Yorkshire
    Posts
    21,375
    Thanks
    221
    Thanked 293 Times in 251 Posts

    Default Re: Plumbing

    Hi Campbell as said cut all your pipe to length, and dry fit it together then mark it with a marker pen so that you get the right angle when you glue it up. Make sure you put solvent weld on both pipe end and inside the fitting then push together and its stuck but make sure the lines you made are lined up. HTH Twiggy:D:D

  9. #9
    Royal Gramma


    Zeus's Avatar
    Join Date
    Nov 2006
    Location
    Irvine, Scotland
    Posts
    1,544
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Plumbing

    Quote Originally Posted by Echobravo View Post
    unfortunately college fine you for having a fish tank in your rm grrr stupid people

    Ed
    Hi Ed, you are kidding right?


    Thanks for the tip Eric, only myself to blame if I f**k it up now. :)

    Campbell
    something broke the surface just to see the starry dome.

    Don't drive faster than your Angel can fly

  10. #10
    Copepod



    Join Date
    Feb 2008
    Location
    Sparsholt UK
    Posts
    20
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Plumbing

    Click here to register & remove adverts
    no i got fined 20 quid for havinf a 6 litre tank in my room apparently would bring down my 6 x 2 x 2 but just sold it on ebay so that out of the questions. one of the second years had a reeftank last year complete with ro unit etc plumbed in 2 the pumbing. i think that may be why they dont like them lol.

    Ed

Page 1 of 2 12 LastLast

Similar Threads

  1. Plumbing
    By lee3871 in forum Marine Hardware / General Qs
    Replies: 4
    Last Post: 01-31-2012, 11:52 AM
  2. Plumbing
    By andylowe04 in forum Marine Hardware / General Qs
    Replies: 5
    Last Post: 07-29-2010, 02:38 PM
  3. Plumbing...
    By Tower in forum Fit Filtration
    Replies: 0
    Last Post: 11-25-2009, 07:25 PM
  4. plumbing parts
    By johnl69 in forum Marine Hardware / General Qs
    Replies: 18
    Last Post: 07-29-2008, 04:39 PM
  5. VDL plumbing
    By sinaarrgghh in forum DIY - And save pounds
    Replies: 2
    Last Post: 07-21-2008, 05:05 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •